EPKK Krakow MSFS V2

[VEX737]

I have the same issue with the installer giving an error saying the simulator path cannot be found.

I have tried modifying InstalledPackagesPath in UserCfg.opt as indicated above but to no avail.

Is there any known solution to this?

[Kris81_pl]

Dzień dobry proszę o informację jakim sposobem można skontaktować się z działem technicznym , dotyczy lotniska EPKK i problemu związanego z nim . Na forum nie mogę tworzyć postów a Inibuilds odsyła do państwa .

[KabanosPL]

Witam, po zainstalowaniu poprawki dodającej stanowiska L i R, symulator ładuje się bez końca. (MSFS24)

[Martin_Starski]

I have the same issue with the installer giving an error saying the simulator path cannot be found.
I have tried modifying InstalledPackagesPath in UserCfg.opt as indicated above but to no avail.
Is there any known solution to this?

Can you tell me the scenery version and the simulator version?

All our installers work the same - they are looking for the file UserCfg.opt in LocalCache:

MS Store:
%localappdata%Packages\Microsoft.Limitless_8wekyb3d8bbwe\LocalCache\UserCfg.opt
Steam:
%appdata%\Microsoft Flight Simulator 2024\UserCfg.opt

And if it's not found, they ask for a manual selection of the correct folder and save that info into the registry. There should be no problems unless something is non-standard in your setup/configuration.

The first option is to make sure that “InstalledPackagesPath” entry in the above-mentioned file points to the path where your Community folder is installed. One user found out that there were extra parentheses (") in paths in the files. It was very strange because they were not visibly shown in the text within the UserCfg.opt file, but they were shown when the installer ran and failed. When he deleted the paths and re-typed them manually, both files started to work fine.

Another possible option is that MSFS is installed on a drive other than C: - the solution is to change the name of "Community" folder, which made the installer unable to recognize it and allowed the user to manually select the location of the MSFS installation folder. Then the entire installation process can be finalized. The last thing is to restore the old folder name.

Last but not least, you can also try to:

1. Remove the patch from UserCfg.opt file, which means that it looks like this: InstalledPackagesPath ""
2. Run our installer, which should ask for the path to the main MSFS folder (incl. Community and Official)
3. Complete the installation
4. Revert the original path to the UserCfg.opt file

If nothing helps, please share the screenshot of the error message + your UserCfg.opt file (it can be attached here, just as a zip file).

[Martin_Starski]

Dzień dobry proszę o informację jakim sposobem można skontaktować się z działem technicznym , dotyczy lotniska EPKK i problemu związanego z nim . Na forum nie mogę tworzyć postów a Inibuilds odsyła do państwa .

Dokladnie tym samym sposobem jakim napisal Pan swoj post - prosze dokladnie opisac problem w watku dedykowanym dla EPKK Krakow MSFS v2, z m.in. informacja z jakiego sklepu jest sceneria, jaka wersja i w jakiej wersji symulatora jest instalowana.

[Martin_Starski]

Witam, po zainstalowaniu poprawki dodającej stanowiska L i R, symulator ładuje się bez końca. (MSFS24)

To byly testowe pliki, ale prosze sprobowac odbudowac SceneryIndexex lub sprawdzic czy nadpisane zostaly wszystkie pliki, w tym m.in. layout.json

[VEX737]

I temporarily deleted the entire UserCfg.opt file and then ran the installer again, that seems to have done the trick.

Thanks for the help!